Netfilter Helpers

Tom Eastep

Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, with no Front-Cover, and with no Back-Cover Texts. A copy of the license is included in the section entitled GNU Free Documentation License.

2020/02/16


Helpers - Introduction

There are a number of applications that create connections dynamically between a client and server. These connections use temporary TCP or UDP ports, so static configuration of firewall rules to allow those connections would require a very lax firewall configuration. To deal with these problem applications, Netfilter supports the concept of a helper. Each helper monitors traffic to/from the default primary port used by the application and opens the firewall to accept temporary connections created by the primary session.

There are helpers for the following applications; default ports monitored by each helper are listed in parentheses:

  • Amanda (UDP 10080)

  • FTP (TCP 21)

  • H323 (UDP 1719, TCP 1720)

  • IRC (TCP 6667)

  • Netbios-NS (UDP 137)

  • PPTP (TCP 1723)

  • SANE (TCP 6566)

  • SIP (UDP 5060)

  • SNMP (UDP 161)

  • TFTP (UDP 69)

Helper Module Loading

In a modular kernel, each helper is typically packaged as two kernel modules. One module handles connection tracking where NAT isn't involved and the other module handles NAT. For example, the FTP helper consists of these two modules (kernels 2.6.20 and later):

  • nf_conntrack_ftp

  • nf_nat_ftp

Note that the naming convention is nf_conntrack_application and nf_nat_application; more about that below.

Prior to Shorewall 4.5.7, helper modules were not auto-loaded and must be loaded explicitly using the modprob or insmod utilities. Beginning with Shorewall 4.5.7, these modules are loaded when Shorewall is determining the capabilities of your system.

Many of the modules allow parameters to be specified when the module is loaded. Among the common parameters is the ports parameter that lists one or more ports that the module is to monitor. This allows running the application on a non-standard port.

Iptables and Helpers

Iptables supports two ways of interacting with modules:

Helper Match

This match (-m helper --helper name) allows selection of packets from connections monitored or created by the named helper.

CT Target

This target (-j CT --helper name ...) , introduced in the 3.4 kernels, allows for explicit association of a helper with a connection.

It is important to note that the name used in iptables is not always the same as the name in the kernel module. Names used in iptables are shown in the following table:

Name of kernel moduleName recognized by iptables
nf_conntrack_amandaamanda
nf_conntrack_ftpftp
nf_conntrack_h323RAS (udp 1719), Q.931 (tcp 1720)
nf_conntrack_ircirc
nf_conntrack_netbios_nsnetbios-ns
nf_conntrack_pptppptp
nf_conntrack_sanesane
nf_conntrack_sipsip
nf_conntrack_snmpsnmp
nf_conntrack_tftptftp

Netfilter helpers present an opportunity for attackers to attempt to breach your firewall by IP address spoofing; See https://home.regit.org/netfilter-en/secure-use-of-helpers/ for a description of the Netfilter facilities available to meet these attacks.

Shorewall Support for Helpers

Shorewall includes support for helpers is several areas. These areas are covered in the sections below.

Module Loading

Shorewall includes support for loading the helper modules as part of its support for loading kernel modules in general. There are several options in shorewall.conf (5) that deal with kernel module loading:

MODULESDIR

This option specifies a comma-separated list of directories where Shorewall will look for kernel modules to load.

MODULE_SUFFIX

Lists the possible suffixes for module names.

LOAD_HELPERS_ONLY

Controls whether Shorewall should load only the helpers and leave the other modules to the auto-loader. This option dramatically reduces the time to process a shorewall start or shorewall restart command.

DONT_LOAD

This is a comma-separated list of modules that you specifically don't want Shorewall to load.

HELPERS

This option was added in Shorewall 4.5.7 and lists the modules to be enabled for association with connections (comma-separated). This option is fully functional only on systems running kernel 3.5 or later.

The module names allowed in this list are amanda, ftp, h323, irc, netbios-ns, pptp, sane, sip, snmp and tftp. If you don't want a particular helper module loaded, then:

  • List it in the DONT_LOAD option; and

  • Explicitly list those helpers that you do want in HELPERS.

AUTOHELPERS

This option was also added in Shorewall 4.5.7. When enabled on systems that support the CT Target capability, it provides automatic association of helpers to connections in the same manner as in pre-3.5 kernels (and with the same vulnerabilities).

The helper modules to be loaded are listed in the file /usr/share/shorewall/helpers. If you wish to customize that file to load only a subset of the helpers or to specify module parameters, then copy the file to /etc/shorewall/ and modify the copy. That way, your changes won't be overwritten the next time that Shorewall is updated on your system.

On systems running a a kernel earlier than 3.5, not all of the helpers can be totally disabled. The following modules can be disabled by using the parameter ports=0 in /etc/shorewall/helpers:

  • ftp

  • irc

  • sane

  • sip

  • tftp

After disabling one or more helpers using this method, you must:

  • Unload the related module(s).

  • Restart Shorewall (use the -c option (e.g., shorewall restart -c) if you have AUTOMAKE=Yes in shorewall.conf (5))..

Note that if you choose to reboot your system to unload the modules, then if you have CT:helper entries in shorewall-conntrack (5) that refer to the module(s) and you have AUTOMAKE=Yes in shorewall.conf (5), then Shorewall will fail to start at boot time.

Iptables

The iptables helper match is supported by Shorewall in the form of the HELPER column in shorewall-mangle (5) and shorewall-tcrules (5).

The CT target is supported directly in shorewall-conntrack (5).

In these files, Shorewall supports the same module names as iptables; see the table above.

Beginning with Shorewall 4.5.7, there is a HELPER column in shorewall-rules (5). In the NEW section, this column allows the explicit association of a helper with connections allowed by a given rules. The column may contain any of the helper names recognized by iptables (see the table above). In the RELATED section, the rule will only match the packet if the related connection has the named helper attached.

Also added in Shorewall 4.5.7 is the HELPER action in shorewall-rules (5). HELPER rules associate the helper listed in the HELPER column with connections that match the rule. A destination zone should not be specified in HELPER rules.

Capabilities

The output of shorewall show capabilities has two entries for each of the helpers listed above that can be disabled by adding ports=0 in /etc/shorewall/helpers.

shorewall show capabilities
   Amanda Helper: Available
   FTP Helper: Not available
   FTP-0 Helper: Available
   IRC Helper: Not available
   IRC-0 Helper: Available
   Netbios_ns Helper: Available
   H323 Helper: Not available
   PPTP Helper: Available
   SANE Helper: Not available
   SANE-0 Helper: Available
   SNMP Helper: Available
   TFTP Helper: Not available
   TFTP-0 Helper: Available
   iptables -S (IPTABLES_S): Available
   Basic Filter (BASIC_FILTER): Available
   CT Target (CT_TARGET): Available
   Kernel Version (KERNELVERSION): 30404
   Capabilities Version (CAPVERSION): 40507

The above output is produced when this /etc/shorewall/helpers file is used on a system running kernel 3.4.4:

loadmodule nf_conntrack_ftp         ports=0
loadmodule nf_conntrack_irc         ports=0
loadmodule nf_conntrack_netbios_ns
loadmodule nf_conntrack_sip         ports=0
loadmodule nf_conntrack_tftp        ports=0
loadmodule nf_conntrack_sane        ports=0

The reason for the double capabilities is that when ports=0 is specified, the iptables name of the helper gets '-0' added to it. So in order for the compiler to generate the correct iptables commands, it needs to know if ports=0 was specified for each of the helprs that support it.

Notice that most of the other helpers are available, even though their modules were not loaded. That's because auto-loading occurs during capability detection on those modules whose iptables name matches the module name.

Kernel >= 3.5 and Shorewall >= 4.5.7

While the AUTOHELPER option described above provides for seamless migration to kernel 3.5 and beyond, we recommend setting AUTOHELPER=No at the first opportunity after migrating. Additionally, you should:

  • Use the HELPER action and the HELPER column in shorewall-rules (5) to attach helpers to only those connections that you need to support.

  • If you run one or more servers (such as an FTP server) that interact with helpers, you should consider adding rules to the RELATED section of shorewall-rules (5) to limit the scope of the helper. Suppose that your Linux FTP server is in zone dmz and has address 70.90.191.123.

    #ACTION               SOURCE                         DEST                      PROTO            DPORT          SPORT
    SECTION RELATED
    ACCEPT                all                            dmz:70.90.191.123                          32768:               ; helper=ftp   # passive FTP to dmz server; /proc/sys/net/ipv4/ip_local_port_range == 32760:65535
    ACCEPT                dmz:70.90.191.123              all                       tcp              1024:          20    ; helper=ftp   # active  FTP to dmz server
    ACCEPT                loc,dmz,$FW                    net                       tcp              -              1024: ; helper=ftp   # passive FTP to net
    ACCEPT                net                            all                       tcp              1024:          20    ; helper=ftp   # active  FTP from net
    DROP:info             all                            all                                                             ; helper=ftp   # 
    SECTION NEW
    HELPER                all                            net                       tcp              21                   ; helper=ftp
    ACCEPT                all                            dmz:70.90.191.123         tcp              21                   ; helper=ftp

Documentation


Frequently Used Articles

- FAQs - Manpages - Configuration File Basics - Beginner Documentation - Troubleshooting

Shorewall 4.4/4.5/4.6 Documentation

Shorewall 4.0/4.2 Documentation


Shorewall 5.0/5.1/5.2 HOWTOs and Other Articles

- 6to4 and 6in4 Tunnels - Accounting - Actions - Aliased (virtual) Interfaces (e.g., eth0:0) - Anatomy of Shorewall - Anti-Spoofing Measures - AUDIT Target support - Bandwidth Control - Blacklisting/Whitelisting - Bridge/Firewall - Building Shorewall from GIT - Commands - Compiled Programs - Configuration File Basics - DHCP - DNAT - Docker - Dynamic Zones - ECN Disabling by host or subnet - Events - Extension Scripts - Fallback/Uninstall - FAQs - Features - Fool's Firewall - Forwarding Traffic on the Same Interface - FTP and Shorewall - Helpers/Helper Modules - Installation/Upgrade - IPP2P - IPSEC - Ipsets - IPv6 Support - ISO 3661 Country Codes - Kazaa Filtering - Kernel Configuration - KVM (Kernel-mode Virtual Machine) - Limiting Connection Rates - Linux Containers (LXC) - Linux-vserver - Logging - Macros - MAC Verification - Manpages - Manual Chains - Masquerading - Multiple Internet Connections from a Single Firewall - Multiple Zones Through One Interface - My Shorewall Configuration - Netfilter Overview - Network Mapping - No firewalling of traffic between bridge port - One-to-one NAT - Operating Shorewall - OpenVPN - OpenVZ - Packet Marking - Packet Processing in a Shorewall-based Firewall - 'Ping' Management - Port Forwarding - Port Information - Port Knocking (deprecated) - Port Knocking, Auto Blacklisting and Other Uses of the 'Recent Match' - PPTP - Proxy ARP - QuickStart Guides - Release Model - Requirements - Routing and Shorewall - Routing on One Interface - Samba - Shared Shorewall/Shorewall6 Configuration - Shorewall Events - Shorewall Init - Shorewall Lite - Shorewall on a Laptop - Shorewall Perl - Shorewall Setup Guide - SMB - SNAT - Split DNS the Easy Way - Squid with Shorewall - Starting/stopping the Firewall - Static (one-to-one) NAT - Support - Tips and Hints - Traffic Shaping/QOS - Simple - Traffic Shaping/QOS - Complex - Transparent Proxy - UPnP - Upgrade Issues - Upgrading to Shorewall 4.4 (Upgrading Debian Lenny to Squeeze) - VPN - VPN Passthrough - White List Creation - Xen - Shorewall in a Bridged Xen DomU - Xen - Shorewall in Routed Xen Dom0

Top of Page